Guides · Bathroom
A washbasin made entirely of marble: can it be done, and how does it hold up?
In brief. A stone washbasin is not a worktop with a hole in it: it is a piece worked in three dimensions, and it is decided in three places — how the bowl is obtained, what happens where the water stands, and who answers for the waste connection. Everything else, maintenance included, follows from those three choices rather than from the name of the stone.
Hollowed from solid or built from panels: what changes?
They are two different objects that often go by the same name. A hollowed basin comes out of a block, or out of a substantial thickness, and the bowl is obtained by removing material: it has no joints, the figure of the stone runs continuously over the rim and into the bowl, and the piece arrives on site finished. A built-up basin is made of cut panels bonded together to form a bowl: it weighs far less, it is priced differently, and it has joints.
The difference is not an aesthetic one. In a built-up basin the joints sit in the worst possible place, which is where water stands longest. A joint made properly, with the right adhesive and the right pressure, lasts for years; a joint made in a hurry, on stone that was not dry, is the first place a dark line will appear. In a hollowed basin that problem does not exist, but another one does: the piece is heavy, and its geometry has to be settled beforehand, because on a solid piece almost nothing can be corrected afterwards.
Anyone who wants a single piece has to accept a dimensional constraint: the bowl is born inside the available thickness, so depth and profile are not as free as they are on a drawing. Anyone who accepts a built-up basin should insist on knowing where the joints will fall, and on seeing them marked on the drawing rather than described in conversation. It is the same logic that governs seam placement on a worktop, which we cover in «a marble top without seams» (/en/guides/marble-top-without-seams).
Why are the rim and the waste the two places where everything is decided?
In a basin water does not pass through: it stands. It stands on the upper rim, where a film is left behind and then evaporates, and it stands around the waste hole, where the jet never quite reaches to rinse. Those are the two places where, after a few months, you can see whether the piece was thought about or merely executed.
On the rim, the profile and the radius are what count: a sharp arris holds the droplet and chips when bottles knock against it, while a rounded rim lets it run off. Around the waste, the fall of the bowl is what counts: if the bottom is too flat, water sits in a ring around the hole and every drying cycle leaves its mark. Even a slight fall, worked in at the finishing stage, changes how the piece behaves for the whole of its life.
The third place, less obvious, is the contact between stone and waste fitting. A natural material, a metal and a gasket live together there, with different rates of expansion and a tightening torque that somebody has to have got right. It is where almost every leak later blamed on the stone actually begins, exactly as it does on worktops: we describe it in «the tap is leaking at its base» (/en/guides/leaking-tap-base-stone-worktop).
Does a marble basin stain and go dull, and if so where?
It does, and it is better to know beforehand than to find out afterwards. Marble is calcium carbonate: acids corrode it, and oily substances can penetrate where the surface is open. In a bathroom acids do not arrive by accident, as they do in a kitchen: they are sprayed on deliberately, because limescale removers work by acid. And the limescale being removed is made of the same substance as the stone, so the product cannot tell the two apart.
The place where it shows first is not the bottom of the bowl, which gets rinsed, but the rim and the surround, where the product is left to act. Anyone choosing a pale stone should expect etching to read as a veil, while on a dark polished surface it reads as a halo: the same damage, read in reverse. We have written two whole guides about this, «marble stains and etching» (/en/guides/marble-stains-and-etching) and «why stone marks sooner in a bathroom» (/en/guides/bathroom-stone-top-marks-sooner), and they are worth reading before the material is chosen rather than after.
The good news is that etching on marble can be reversed in place, because the work is done in the thickness of the stone: a piece is re-polished for what it is, with nothing to rebuild. We explain how in «re-polishing dull marble in place» (/en/guides/repolish-dull-marble-on-site).
Which finish belongs inside the bowl?
Polished is the easiest to clean and the least forgiving: it reflects, so it shows every trace of corrosion. Honed and satin finishes forgive the eye far more, but their surface is slightly more open and holds soap residue more readily, which has to be rinsed off rather than left to dry. A brushed finish, handsome on a worktop, is a choice you pay for inside a bowl: the texture holds.
In practice the combination that survives best is a less reflective finish on the outside, where the piece is looked at, and the most closed surface possible on the inside, where it is cleaned. We have already dwelt on finishes and on what they imply over time in «the finish of a marble table top» (/en/guides/marble-table-top-finish).
How much does it weigh, and what is it sitting on?
A hollowed basin concentrates a great deal of weight into a few square centimetres, and that weight never arrives alone: hands lean on it, the tap gets pulled, somebody stands on it to change a bulb. The cabinet or bracket below has to be sized for the piece full of water and for sideways thrust, not for the dry weight on the datasheet.
Two practical consequences follow. The first is that the structure must be settled together with the piece and not after it: the bearing points and any reinforcement belong on the drawing. The second is that the route up has to be measured before cutting — stair well, lift, doorways — because a solid basin cannot be taken apart. On weight and how it is worked out we have a guide of its own, «how much does a stone top weigh» (/en/guides/how-much-does-a-stone-top-weigh).
Who fits the waste, and who answers if it leaks?
This is the question that matters most, and it should be settled in writing before the order. On most jobs whoever supplies the basin delivers it worked and drilled, while the waste fitting, trap and tap are installed by the plumber. If that is not written down, the first drip turns into an argument: the supplier will say the hole is to size, and the plumber will say the stone is not flat.
Three lines are worth putting in the order: the size and tolerance of the waste hole, together with the fitting it was calculated for; who supplies the gasket and who does the tightening; and who carries out the water test, when, and with whom present. A test with the bowl full, done by two people and recorded with a date, settles in advance the longest part of the arguments that arise later.
How we work
We do not use resin to stiffen our slabs: where a surface is large the correct answer is a support, and the mesh applied to the back is already a sound backing. On a basin this matters more than elsewhere, because an unresined surface is re-polished for what it is, without having to rebuild a treatment somebody else applied.
The geometry of the bowl — depth, radii, fall, the size of the hole — is settled on the drawing, before the stone goes into the machine: on a piece cut from solid, almost nothing can be corrected afterwards. For a bathroom supplied to a project — a hotel, a run of rooms — the scale changes and the substance does not: the pieces need to come from the same batch, and material needs to be left over for replacements. The route is the one described in the contract (/en/contract) section; the stones and the work can be seen in the collections (/en/collections) and in the works (/en/works), and the contact details (/en/#contatti) lead to the people who follow the fabrication.
Can a marble basin be used every day?
Yes. What changes is not the use but the cleaning: water and a neutral soap, rinsed and dried, and no acid limescale remover. In a bathroom the damage almost always comes from the wrong product used with the best of intentions.
Hollowed from solid or built from panels?
Solid has no joints and is the sounder choice exactly where water stands; a built-up basin weighs less, costs less and allows freer shapes. If the built-up version is chosen, the position of the joints should be seen on the drawing before ordering.
Can the basin be made in the same marble as the top?
It can, provided the material is set aside at the same time: it is the batch that guarantees the match, not the name of the stone. Ask for it to be reserved before the top is cut, not afterwards.
Can a chipped rim be repaired?
In most cases yes, and the work is done in place. Chips on the rim of a bowl are treated like chips on a worktop: we cover it in «repairing a chipped marble top» (/en/guides/repair-chipped-marble-top).
Is onyx suitable for a washbasin?
It is a more delicate stone and more sensitive to acids, and in a basin it works in severe conditions. Where it is chosen, it is almost always for a surface that is looked at more than it is used, and the decision should be taken in that knowledge.
Ask for a quotation The tables collection
This page sets out assessment and selection criteria; it quotes no prices, no intervention times and no company case studies. The fabrication indications are those of good stoneworking practice and have to be checked against the actual case, because they depend on the stone, the dimensions and the supporting structure. No technical standard is cited, because requirements change with the intended use of the room.