Guides · Technical
Who builds the light box under a backlit stone top, and in what order is the work done?
In short. A backlit top is not a slab with a light under it: it is a box. Three things have to share the same few centimetres: the gap the light needs, the bearing the stone needs, and the access the wiring will need in a few years’ time. The joiner builds the void and the electrician installs the lighting, but the one who should draw it is whoever works the stone. And the point that derails almost every project is always the same: the part of the top that projects past the cabinets needs support, and support is opaque.
What is the box, in practice?
It is a closed void beneath the stone, with six necessary parts: a pale base and sides, which bounce stray light upwards; the source, a diffuse panel or strips; an air gap; an opal diffuser, if the source is made of point emitters; the places where the stone actually bears; and an opening to get back in without removing the top. The drivers sit outside, somewhere ventilated and reachable.
It becomes hard the moment you measure the height available inside a cabinet: a few centimetres, claimed at once by the light, which without a gap draws a row of bright spots, and by the stone, which without bearing bends. The space is reserved when the cabinet is drawn, not afterwards: on the gap and the quality of the light we wrote the guide Backlit onyx: LEDs, light and heat.
Why is the bearing the real problem?
On an ordinary top the slab does not bear only on the cabinet sides: underneath there is a continuous deck that spreads the load, and it runs past the cabinets to carry the overhang. An installer sums up the practice in an electricians’ discussion from December 2025, opened by someone asking how a worktop is lit from below: «typically the plywood decking extends beyond the cabinets to support the overhanging portion». And it is exactly the thing you cannot do under a stone that has to light up.
In the same thread two difficulties go unanswered: how do you light the part that projects, when that is precisely where support is needed; and the fact that a source placed under the top also lights the inside of the cabinet. After eleven messages the conclusion is that no panel on the market works over the overhang «without some sort of mounting apparatus», and that nobody knows whether such a support can be built.
It can, but the other way round: not a continuous, blind deck, but a discontinuous bearing that belongs to the lighting layout. Four routes, chosen before the slab is ordered: reduce the overhang, the simplest and most overlooked; move the bearing to the perimeter, with a frame along the edges and the centre clear; use brackets where the light does not reveal them; or support the slab from behind with a mesh the light passes through, as we do with onyx. How far stone can project before it needs support is the subject of the guide How far can a stone top overhang without support.
Who builds it: the joiner, the electrician or the stone fabricator?
On site the division is always the same: cabinet and void to the joiner, sources and wiring to the electrician, the stone to the fabricator. The trouble is that none of the three holds, on their own, the piece of information that governs everything else: translucency is not a property of the material in general, but of that particular slab.
In installers’ forums you read it between the lines. In a 2008 discussion about an onyx worktop, the member who had done a similar job warns that these tops are «extremely fragile» and adds the most useful line in the thread: «they have to build a box». Another, after a restaurant job, concludes that the right thing is to get the countertop manufacturer and a lighting representative around the same table.
Our answer is a different division: drawing the box belongs to whoever works the stone, building it belongs to the joiner and the electrician. Not out of hierarchy: the internal height of the void, the gap to the source and the position of the bearings follow from the thickness and the transparency of the slab, and those are only visible against the light, before cutting.
In what order is the work done?
The order matters more than the materials: every step taken out of sequence is paid for with a piece to remake.
- Slabs are chosen against the light, before cutting, and the layout of the pieces is decided;
- An offcut of that same slab is tested with the intended source: out of it comes the gap to reserve, whether a diffuser is needed, and the colour temperature;
- The void is drawn with that dimension inside it, with the bearing points and the maintenance opening;
- The joiner builds the cabinet with the void in it, rather than fitting a void into a cabinet already made;
- The electrician runs the circuits and keeps the drivers out of the cavity;
- The light is switched on with the stone resting in place and not yet bonded, and everyone looks at it;
- The top is fitted for good and signed off with the light both on and off.
The step nearly always skipped is the sixth, the only one that costs almost nothing: after bonding, every correction is a demolition job.
And the cutouts for the sink, the hob and the sockets?
Fitters always ask the same questions, written word for word in the electricians’ threads: how much gap between the light sheets and the stone, how to cut the sheets around the openings, whether to lay plywood first, whether spacers are needed. The answer covering all of them: cutouts are a drawing problem, not a cutting problem, and the drawing comes first.
In stone a cutout is already where cracks begin, as we explain in Cracks at sink and hob cutouts. Under a light it also becomes a hole in the lighting layout: the edge reads as a halo, and should be closed with a deliberate opaque band. The source is not cut wherever convenient: a light sheet has a circuit, interrupted only where its maker allows. The frame that carries an undermount sink, the subject of Undermount sink: what actually holds it up, is opaque and bulky: it has to enter the lighting layout on day one. A hob, finally, brings heat over a closed cavity, and that is the combination to avoid.
What to test before the cabinet is closed?
A lights-on test, with the stone resting in place, takes half an hour and tells you five things: whether the light is even or the row of spots shows; whether the joints light differently; whether the surface is warm after a few hours, which it should not be; whether the panels, when there is more than one, are the same shade, because across a pale surface a tiny difference shows; and how the top looks with the light off.
What stays reachable afterwards?
In the December 2025 discussion one member asks the most practical question of all — how the light is replaced when it fails — and nobody answers. For the box to make sense it needs a removable panel, drivers outside the cavity and a way of reaching them without lifting the top: a slab bonded in front of the sources turns a ten-euro component swap into a building site.
How we work
At Stoneform, backlighting is a design question before a site question. We look at every slab against the light before cutting; we do not use resin to reinforce slabs, and where a large surface needs support we apply a mesh to the back that the light passes through without drawing shadows. We work the stone in our own factory: void, bearings and serviceability are decided with the joiner and the electrician, not after them. LuxOnyx, the modular system designed by Giuseppe Fallacara and Andrea Sgherza, sums up this way of working; our other luminous pieces are in the Sculpture and lighting collection.
For bar counters, islands and lobbies in hotels and residences, our Contract page explains how we follow projects. For a quotation, simply write to us with dimensions and photos of the space: we reply within 48 hours.
Frequently asked questions
Who should actually build the light box?
The joiner or cabinetmaker builds the void and the electrician installs the lighting. The one who should draw it is whoever works the stone: internal height, the gap to the source and the bearing points follow from that slab and its thickness, not from the cabinet.
Can a kitchen worktop in daily use be backlit?
It can, but backlighting sits badly with a real working surface: it calls for a thin slab, a discontinuous bearing and a spotless surface, because against the light everything shows. It works far better on islands, bar counters and upstands.
Is plywood needed under the stone?
Under an ordinary top a continuous deck spreads the load. Under a backlit top it is unusable, because it is opaque: the bearing moves to the perimeter, onto a frame or onto brackets, and the centre is left clear for the light.
Can lighting be added to a top that is already fitted?
Rarely with a good result. Void, internal height and bearing are decided before the slab is ordered: once the top is fitted the space is not there, and the slab chosen may not be translucent.
Ask for a quotation The tables collection
The quoted lines come from three public electrical installers’ discussions, read in full: «Backlighting for an Onyx Countertop» (2008, fifteen messages), «Under Onyx counter top Lighting» (June 2021, four messages) and «Backlit Kitchen Countertops» (December 2025, eleven messages), on the Mike Holt forum. They are the opinions of tradespeople, not requirements. The notes on bearings and overhangs are workshop rules: the design figure is the declared flexural strength of the slab, measured to EN 12372 for natural stone and EN 14617-2 for agglomerated stone, and it should be asked of the supplier. The electrical installation, residual-current protection and ingress-protection ratings in bathrooms remain the responsibility of the designer and the electrical installer, under IEC 60364-7-701 (CEI 64-8 section 701 in Italy, BS 7671 section 701 in the UK).